|
|
|
您当前所在的位置:返回首页 >> 产品中心 |
|
双股刺绳机CS-A |
【更新时间:2015-06-16】 【点击次数:25次】 【字体:大 中 小】 【打印】 【关闭】 |
1、刺网机说明
一、用途、性能
该机主要适用于生产各种多股刺钢丝,其使用材料应符合GB/T343-94标准要求《一般用途热镀锌低碳钢丝》,该产品广泛使用于国防、铁路、调整公路、农畜牧等行业。
CS-A型刺钢丝机由绕丝和收丝加捻二部分连接组成(见图书1、图2),并配套四只放丝盘,该机各部件工作协调,动作平稳,操作灵活可靠,是生产刺钢绳的专用设备。
二、主要技术参数
1、CS-A型刺钢丝机的主要技术参数见表2 |
序号 |
项目 |
单位 |
基本参数 |
1 |
电动机 |
KW |
2.2 |
2 |
主传动轴转速 |
r/min |
432 |
3 |
理论产量 |
Kg/h |
90 |
4 |
整机重量 |
kg |
1200 |
5 |
主机部分 |
mm |
1900×1300×980 |
6 |
收绳加捻部分 |
mm |
1800×750×750 |
注:特殊需要按供需双方约定。
2、刺钢绳的规格范围见表2 |
序号 |
项目 |
单位 |
基本参数 |
1 |
刺距 |
mm |
76(3寸)102(4寸) |
2 |
捻数 |
个 |
4 |
3 |
股丝直径 |
mm |
2.2-2.8 |
4 |
刺丝直径 |
mm |
1.8-2.2 |
1, gill nets machine instructions
1, uses, performance
Machine is mainly applicable to the production of a variety of multi-strand barbed wire, the use of materials should meet the standard requirements GB/T343-94 "general purpose hot-dipped galvanized low carbon steel wire," the products are widely used in national defense, railway, adjust the highway, agricultural livestockand other industries.
CS-A-type barbed wire around the wire machine and the income from the two parts connected to form a filament twist (see Book 1, Figure 2), and matching silk put four plates, coordinating the work of the various components of the aircraft movements, stable, flexible operation and reliable,is the currently the only product barbed rope equipment.
2, the main technical parameters
1, CS-A-type barbed wire machine Main technical parameters of Table 2 |
No. |
Item |
Units |
Basic parameters |
1 |
Motor |
KW |
2.2 |
2 |
Main Drive Shaft Speed |
r/min |
432 |
3 |
Theoretical yield |
Kg/h |
90 |
4 |
Total Weight |
kg |
1200 |
5 |
The host part of the |
mm |
1900×1300×980 |
6 |
Size of the pull-twist part of the |
mm |
1800×750×750 |
Note: special needs agreement by both supply and demand.。
2, barbed wire line the scope of the specifications in Table 2 |
No. |
Item |
Units |
Basic parameter |
1 |
distance |
mm |
76(3Inch)102(4Inch) |
2 |
Twist number |
piece |
4 |
3 |
Unit wire diameter |
mm |
2.2-2.8 |
4 |
Barbed wire diameter |
mm |
1.8-2.2 |
|
|
|